![groovypost create windows 10 bootable usb flash drive groovypost create windows 10 bootable usb flash drive](http://www.mswhs.com/wp-content/uploads/2012/01/Wake-for-Backup.png)
- GROOVYPOST CREATE WINDOWS 10 BOOTABLE USB FLASH DRIVE INSTALL
- GROOVYPOST CREATE WINDOWS 10 BOOTABLE USB FLASH DRIVE ZIP FILE
- GROOVYPOST CREATE WINDOWS 10 BOOTABLE USB FLASH DRIVE PC
GROOVYPOST CREATE WINDOWS 10 BOOTABLE USB FLASH DRIVE PC
Windows image file boot (WIMBoot) lets you set up a PC so that it runs directly from a compressed Windows image file (WIM file). Hence, it only targets new computers with small SSD or eMMC-based hard drives. WIMBoot are subject to a performance hit. wimboot - new, available for UEFI systems.use it for testing booting via qemu menu: MultiBootUsb-8.8.0 > Boot ISO/USB > Boot USB >.Download windows 10 iso (media creation tool).Which is NOT what you want.Write iso to a flash drive without overwriting data (but overwriting other bootable stuff)Ĭreate Dual Boot Windows10 & Ubuntu flash disk Download both Once the installation is done (it'll take a while), then once it reboots, if you don't do anything, it'll start the installation process again. Your thumb drive will also be displayed here so be careful not to delete that. It will give you an error if you don't delete both partitions. Delete both partitions and then create a new partition combining both and select that partition to install. Over here I had one small partition (100 or 400 MB, sorry can't remember) and a ~50GB partition. It takes a little bit of time so let it go up to the step where you have to select which drive to install. Go to the last page and select your thumb drive from the override boot list. Insert the USB thumb drive to the LattePanda and reboot. If you are using a Mac, use Bootcamp Helper to create a bootable USB The file I downloaded from LattePanda (which was supposed to be put to the root of the thumb drive did not work)
GROOVYPOST CREATE WINDOWS 10 BOOTABLE USB FLASH DRIVE INSTALL
I tried resetting BIOS, tried doing the WINPE usb thumb drive thing, tried install Ubuntu, but nothing worked. It would show the LattePanda logo wait a while and then reboot. I'm not sure what happen that mines came with a corrupt operating system, but I going to reach out to the LattePanda Team to inform them of this issue. The LattePanda restated and finally got prompted with the first time setup to select the language, keyboard, and time zone. Then I was prompted with Sysprep to a cleanup out-of-the box setup, click on okay. Once logged in some sort of command line came up and did some work and went away after a minute. It then started normally and logged in as Administrator. Then once the screen was off I unplugged the USB drive and let the LattePanda boot up for the first time after being imaged, it side getting ready went all the way to 100% and after it rebooted. Once it was done it will ask for you to type exit to reboot the LattePanda. With the LattePanda off I plugged the USB drive in to the USB 3.0 port and powered on the LattePanda and it automatically started the imaging process. Extracted all the file to my computer, then copied the file only to the root of the USB drive. Formatted an 8GB USB drive (Sandisk Cruzer) to FAT32.
GROOVYPOST CREATE WINDOWS 10 BOOTABLE USB FLASH DRIVE ZIP FILE
Downloaded the Zip file (5.9GB) took like 30 minutes to download. I decide to reload the operation system exactly the way instructed. So I started to look up to see if anyone else had the same issue and I didn't find mush other than a few guys on the LattePanda forums saying to reload the operating system, but they were not about to do it the way instructed on the LattePanda website. 20 minutes pass and still on "Just a moment". The first thing I see is the LattePanda logo, then it goes straight to "Just a moment".ĥ minutes pass and it still on "Just a moment" so I wait some more time.